Updated Nov 22, 2026· 8 min read

Key takeaways

  • Compare the best dock bumpers for fixed dock protection, from foam pads and corner guards to piling bumpers, with sizing, materials and mounting tips.

Disclosure: As an Amazon Associate, I earn from qualifying purchases.

Our top pick: Better Boat 48-Inch Dock Bumper. Runner-up: Extreme Max BoatTector Dock Bumper, Large Corner, 3006.7333.

Every dock has hard places a hull should never meet directly: a square timber edge, a steel corner, or a round piling where a bow swings in a crosswind. Dock bumpers solve that permanently. Unlike boat fenders, which hang from the boat and travel with it, dock bumpers and dock edging are fixed to the dock with screws or bolts, so protection is in place before a boat arrives and stays when it leaves.

Coverage, profile shape, and cushion depth matter more than portability, and fasteners matter as much as the pad. A good setup combines forms: horizontal edging or foam pads along the main face, vertical bumpers on pilings and posts, and a corner piece where two faces meet. The five picks below cover those jobs with five different brands, and the buying guide after the list helps you decide how much coverage your slip needs.

1. Better Boat 48-Inch Dock Bumper

The Better Boat 48-inch bumper is the most flexible starting point on this list. It is a foam-filled pad with a 6-by-4-inch profile and a full 4 inches of cushion depth, so when a hull leans into the dock in chop, the pad keeps compressing instead of bottoming out against the timber.

The core is high-density closed-cell foam, which does not absorb water and holds its shape through repeated contact. Around it sits a UV-resistant vinyl and polyester tri-laminate cover with double thermal-bonded seams. Stainless steel screws are included, and the pad fixes horizontally along an edge or vertically on a post or piling. At 48 inches, one pad protects the main contact zone in a single slip.

Specs

  • Brand: Better Boat
  • Profile: 6 x 4 inches, foam-filled pad
  • Length: 48 inches
  • Core: High-density closed-cell foam
  • Cover: UV-resistant vinyl and polyester tri-laminate, double thermal-bonded seams
  • Mounting: Stainless steel screws included, horizontal or vertical
  • ASIN: B0CP6GHHYX

2. Extreme Max BoatTector Dock Bumper, Large Corner, 3006.7333

Corners concentrate force: a hull that glances along a flat face can dig into a square corner and take gelcoat damage in one contact. The Extreme Max BoatTector 3006.7333 is a large corner piece measuring 12 by 12 inches around the corner, with a 6-inch height and 4-inch cushion depth.

Inside is closed-cell foam padding that will not deflate or collapse, so there is no valve or air pressure to maintain. The cover is a marine-grade tri-laminate described as UV and tear resistant, with double thermal-bonded seams, and four corrosion-proof polycarbonate grommets provide the mounting points.

This is the right shape for the outside corner at a slip entrance or the end of a finger pier. Pair it with straight pads along the adjoining faces and the corner stops being the weak point. The listed color is white, which makes contact marks easy to spot.

Specs

  • Brand: Extreme Max
  • Model: 3006.7333 BoatTector
  • Type: Corner bumper
  • Dimensions: 12 x 12 x 6 x 4 inches
  • Core: Closed-cell foam, non-deflating
  • Cover: Marine-grade tri-laminate, UV and tear resistant
  • Mounting: 4 polycarbonate grommets
  • UPC: 814166022840
  • ASIN: B0156K2ABA

3. Dock Edge DocKushion Premium Foam Dock Bumper, Large, DE1150F

The DocKushion system from Dock Edge takes a different approach from single pads. The Large bumper, part 1150-F, is a 48-inch modular section with an expanded polypropylene foam core wrapped in an integral polyurethane skin carrying UV inhibitors and fungicides. Sections connect end to end, so a long face gets a continuous cushion instead of separate pads with gaps.

That continuity is the main reason to choose this design: a hull sliding along the face meets the same surface the whole way, with no unprotected timber between pads. The Large profile measures 48 by 2 by 4 inches in the Dock Edge catalog, a slimmer face than the deep foam pads above, which suits docks where a bulky pad would crowd a narrow finger. The wider DocKushion family includes smaller sections, corner pieces, and end caps, so a layout can turn corners and finish ends with matching parts. Measure the face and count sections before ordering.

Specs

  • Brand: Dock Edge
  • Model: DE1150F, DocKushion Large (1150-F)
  • Length: 48 inches
  • Profile: 48 x 2 x 4 inches
  • Core: Expanded polypropylene foam
  • Skin: Integral polyurethane with UV inhibitors and fungicides
  • Format: Modular, connects end to end for long runs
  • Color: Putty
  • ASIN: B0041U8J9E

4. Attwood SoftSide Round Corner Dock Fender, 93534-1

Attwood’s SoftSide line is built around a simple idea: a molded, one-piece fender with no inflation valve. The 93534-1 is the round corner version, a 15-inch bumper shaped for a dock corner. Being a solid molded piece of lightweight polymeric material, there is nothing to puncture, top up, or find flat at the start of the season.

The polymer is soft to the touch, easy on hull finishes, and resistant to UV exposure and chalking. At 7 inches thick, it puts generous material between hull and corner. Installation is bolt-on, so the bumper stays aligned with the corner it protects.

Choose this shape when the problem spot is a single corner rather than a long face. Its round profile deflects glancing contact instead of catching a rub rail. For boats in the same slip every day, it removes one recurring chore from dock upkeep.

Specs

  • Brand: Attwood
  • Model: 93534-1
  • Type: Round corner dock fender
  • Dimensions: 7 x 7 x 15 inches
  • Thickness: 7 inches
  • Material: Molded lightweight polymeric material, UV and chalk resistant
  • Installation: Bolt-on, no inflation valve
  • UPC: 022697935342
  • ASIN: B01J26LRSQ

5. OCEANBROAD Dock Piling Bumpers, 48-Inch, 2-Pack

Pilings need vertical protection over a range of heights, because water levels and hull freeboard change. The OCEANBROAD pair addresses that job directly: each bumper is 48 inches long, inflatable, and shaped with a concave inner surface at 6.2 by 3.5 inches so it wraps against a round post instead of bridging across it.

The body is marine-grade PVC described as UV and saltwater resistant, with a stainless steel hardware kit listed as 16 screws and 16 washers and recessed mounting holes to keep fastener heads away from the hull. Inflation lets you set firmness, softer for light boats and firmer where heavier hulls lean on the piling. At about 7.76 kilograms packaged, the pair is substantial, matching its role on exposed outer pilings.

Fit matters most here. The concave profile is made for round pilings, so measure your post diameter before ordering. Square posts are better served by a flat pad mounted vertically, such as the first pick on this list. On the right pilings, a 48-inch vertical bumper covers the contact band through typical tide and wake movement.

Specs

  • Brand: OCEANBROAD
  • Type: Piling bumpers, 2-pack
  • Length: 48 inches each
  • Profile: 6.2 x 3.5 inches, concave inner surface for round pilings
  • Material: Inflatable marine-grade PVC, UV resistant
  • Hardware: Stainless steel screws and washers included
  • Mounting: Vertical, on posts and pilings
  • ASIN: B0GGQQBRRP

How to Choose the Best Dock Bumpers

Start by mapping contact points. Note where a hull can touch: the long face, the outside corners, and each piling or post inside the slip. Each zone wants a different form, and mixing forms protects better than repeating one form everywhere.

Horizontal edging and pads guard the main face. Continuous PVC or vinyl edging gives unbroken coverage and suits light, frequent contact. Foam pads give deeper cushion in a shorter section, better where boats sit against the dock or wake action works the hull against the face. Modular foam systems join sections into long runs with pad-like cushioning. Vertical post bumpers guard pilings: a curved or concave profile wraps a round piling, while a flat pad mounted vertically suits a square post. Length should cover the band where the hull rides with tide and wake; 48 inches is a common working length. Corner bumpers guard the points, where angled hits concentrate, so use a piece shaped for the corner rather than butting two straight sections together.

Material decides lifespan. Marine-grade vinyl and PVC resist water and clean easily, and versions with UV inhibitors and fungicides resist chalking and mildew. Tri-laminate covers over closed-cell foam combine a tough skin with a core that cannot waterlog. EVA foam skips inflation, inflatable PVC lets you tune firmness but needs pressure checks, and solid molded polymer trades softness for zero maintenance. Cushion depth is protection: around 4 inches or more gives heavier boats more travel before the hull reaches the dock structure, while thinner edging suits light boats in sheltered water.

Finally, plan the installation. Most fixed bumpers mount with stainless screws or bolts into the dock framing, not just deck boards, and recessed fasteners keep metal away from the hull. Keep bumpers distinct from boat fenders: fenders hang from the boat for visiting docks, while bumpers stay on your dock for the slip you use most.

Frequently Asked Questions

What is the difference between dock bumpers and boat fenders?

Dock bumpers are fixed to the dock with screws or bolts and protect one location permanently. Boat fenders hang from the boat and protect the hull at any dock it visits. Many owners use both: bumpers for the home slip, fenders for travel.

How many dock bumpers does a slip need?

Cover each contact point rather than chasing a number. A typical slip needs protection along the main face, on reachable pilings, and on any exposed entrance corner. Divide the face length by the bumper length for a count, then add post and corner pieces.

Should dock bumpers be mounted horizontally or vertically?

Both, in different places. Horizontal mounting suits long faces where a boat lies alongside. Vertical mounting suits pilings and posts, where contact happens over a band of heights as water levels change. Many foam pads work in either orientation.

How do I maintain fixed dock bumpers?

Rinse off salt and grime, check fasteners for looseness or corrosion each season, and inspect covers for tears or UV chalking. Inflatable models need occasional pressure checks. Replace a bumper that has torn loose or split.

Conclusion

The best dock bumper setup is a small system, not a single product. Use a deep foam pad such as the Better Boat bumper for the main contact zone, a shaped corner piece such as the Extreme Max BoatTector or Attwood SoftSide where hulls turn in, a modular DocKushion run for a long face, and vertical OCEANBROAD bumpers on round posts. Match each form to its contact point and fix it with stainless hardware into solid framing.

U
US Sport Update Editorial Team
We compare specs, materials and verified owner reviews before a product earns a spot. Rankings are never paid.
Affiliate disclosure. As an Amazon Associate we earn from qualifying purchases at no extra cost to you. Prices accurate as of the date shown.
Best Dock Bumpers: 5 Fixed Guards for Safer…Check price on Amazon

More from Amazon

Programs that pair well with the guide above. Offers and eligibility are set by Amazon and may change.

Amazon Prime

Free shipping on eligible items, Prime Video and more. Eligible new members can start with a free trial.

Start a Prime free trial
Prime for Young Adults

A Prime membership for ages 18-24 with a trial period. Eligibility is set by Amazon.

See Prime for Young Adults
Audible

Audiobooks and podcasts to listen to on the go. Eligible new members can start with a free trial.

Try Audible free
Amazon Music Unlimited

Ad-free music streaming. Eligible new subscribers can start with a free trial.

Try Music Unlimited free

As an Amazon Associate we earn from qualifying purchases.